108
edits
Changes
Jump to navigation
Jump to search
Line 67:
Line 67: − + − + − + − DSi software is always writing just ZERO to bit11-6 though? Maybe the hardware does automatically know which SD/MMC CMDs and ACMDs have data? Or maybe data is always automatically transferred when receiving a data-startbit, or when writing to data register - and bits like NTDT would be needed only for things like proper data timeout handling?+ + + +
SD/MMC/SDIO Registers (view source)
Revision as of 12:42, 2 September 2015
, 12:42, 2 September 2015→4004800h/4004A00h - SD_CMD - Command and Response/Data Type (R/W)
===4004800h/4004A00h - SD_CMD - Command and Response/Data Type (R/W)===
===4004800h/4004A00h - SD_CMD - Command and Response/Data Type (R/W)===
15 undoc Unknown/undoc (read/write-able)
15 undoc Unknown/undoc (read/write-able)
14 undoc Security Cmd (0=Normal, 1=Whatever/Security) (sdio?)
14 undoc Security Cmd? (0=Normal, 1=Whatever/Security?) (sdio?)
13 undoc Data Length (0=Single Block, 1=Multiple Blocks)
13 undoc Data Length (0=Single Block, 1=Multiple Blocks)
12 undoc Data Direction (0=Write, 1=Read)
12 undoc Data Direction (0=Write, 1=Read)
11 NTDT Data Transfer (0=No data, 1=With data)
11 NTDT Data Transfer (0=No data, 1=With data)
10-8 REP2-0 Response Type (0..2=Unknown/Reserved, 3=None, 4=48bit,
10-8 REP2-0 Response Type (0=Auto, 1..2=Unknown/Reserved, 3=None, 4=48bit,
5=48bit+Busy, 6=136bit, 7=48bitOcrWithoutCRC7)
5=48bit+Busy, 6=136bit, 7=48bitOcrWithoutCRC7)
7-6 CMD1-0 Command Type (0=CMD, 1=ACMD, 2..3=unknown, maybe GEN WR/RD?)
7-6 CMD1-0 Command Type (0=CMD, 1=ACMD, 2..3=unknown, maybe GEN WR/RD?)
5-0 CIX Command Index (0..3Fh, command index)
5-0 CIX Command Index (0..3Fh, command index)
Invalid values can cause ILA error (particulary on setting NTDT for CMD12, or for CMD's Response=None). ILA error will also occur if an old CMD is still busy.<br>
Setting Command Type to "ACMD" is automatically sending an APP_CMD prefix prior to the command number. For Multiple Blocks, the hardware supports automatically sending STOP_TRANSMISSION after the last block.<br>
DSi software is usually setting Response Type to "Auto", which is causing the hardware to use the correct response/data type for standard SD/MMC commands (bit11-13 are ignored/should be zero when using "Auto"; and maybe same for bit14-15?).<br>
One exception is that the DSi firmware isn't using "Auto" for SDIO commands (maybe the hardware isn't aware of them; or it's unable to distinguish between read/write direction of CMD53, which would require examining the command's PARAM bits).<br>
There might be subtle differences between some SD and MMC commands, unknown if/how "Auto" is working in that cases; unknown if there's a SD-or-MMC mode select bit for that purpose in some configuration register.<br>
Invalid values can cause ILA error (particulary on setting NTDT for CMD12, or for CMD's Response=None). ILA error will also occur if an old CMD is still busy.
===4004804h/4004A04h - SD_CMD_PARAM0-1 - Argument (32bit, 2 halfwords) (R/W)===
===4004804h/4004A04h - SD_CMD_PARAM0-1 - Argument (32bit, 2 halfwords) (R/W)===