DSi XL testpoints
Jump to navigation
Jump to search
UTL-CPU-01 testpoints
number | name (TWL testpoint) | voltage standard | comment |
---|---|---|---|
TP1 | EXTB+ | ? | |
TP2 | VIN | ≃5V DC | External charger power input |
TP3 | Rosc | ? | ? |
TP4 | RICHG | ? | Recharge? |
TP5 | GND | ground | (near external charger connector) |
TP6 | VDD12 (aka V12) | 1.2V power rail | CPU-TWL core voltage |
TP7 | BT+ | battery + | at 2-pin power connector to UTL-SUB-01 |
TP8 | VDET- | ? | ? |
TP9 | DET | ? | ? |
TP10 | VDD18 (aka V18) | 1.8V power rail | Various I/O and core voltage (incl. RTC) |
TP11 | ? | ? | something charging? |
TP12 | VDD10 | 10V power rail | For LCDs |
TP13 | VDD33 (aka V33) | 3.3V power rail | Various I/O and core voltage |
TP14 | GND | ground | (near PMIC) |
TP15 | B+ | ? | battery + ? |
TP16 | VDD-5 | -5V power rail | For LCDs |
TP17 | PVDD | ? | ? |
TP18 | VDD5 | 5.0V power rail | For LCDs |
TP19 | SG? | ? | ? |
TP20 | BLA1 | ? | backlight anode for lower screen |
TP21 | VDD42? | 4.2V? power rail (it's certainly a power rail) | generated from VDD5 using diode voltage drops? (to D6, C22, D3) |
TP22 | BLC1 | ? | backlight cathode for lower screen |
TP23 | BLA2 | ? | backlight anode for upper screen |
(TP24, TP25 don't exist) | |||
TP26 | BLC2 | ? | backlight cathode for upper screen |
(TP27 doesn't exist) | |||
TP28 | MIC- | ground | same net as (analog) ground |
TP29 | MIC+ | analog | Analog microphone-in signal |
TP30 | SPRP | analog | positive signal for right built-in speaker |
TP31 | SPRN | analog | negative signal for right built-in speaker |
TP32 | SPLP | analog | positive signal for left built-in speaker |
TP33 | SPLN | analog | negative signal for left built-in speaker |
TP34 | GND | ground | probably analog ground |
TP35 | SR | analog | headphone tip |
TP36 | SL | analog | headphone ring |
(TP37, TP38 don't exist) | |||
TP39 | ORANGE | 3V3? 4V2? (at anode) | Orange LED charging indicator |
TP40 | BLUE | 3V3? 4V2? (at anode) | Blue LED power good indicator |
TP41 | RED | open collector (connected to LED cathode) | Red LED battery low indicator |
TP42 | MC1_D7 | 3V3 | MSB of gamecard parallell ROM *or* AUXSPI COPI signal |
TP43 | MC1_D6 | 3V3 | 6th bit of gamecard parallell ROM *or* AUXSPI CIPO signal |
TP44 | MC1_VCC | 3.3V power | power supply to gamecard (can be switched off by SoC) |
(TP45 doesn't exist) | |||
TP46 | MC1_D5 | 3V3 | |
TP47 | MC1_D4 | 3V3 | |
TP48 | MC1_D3 | 3V3 | |
TP49 | MC1_DET | 3V3 | Cartridge detected in slot (active-low) |
TP50 | MC1_D2 | 3V3 | |
TP51 | MC1_IREQ | 3V3 | gamecart->SoC IRQ |
TP52 | MC1_D1 | 3V3 | |
TP53 | MC1_RES | 3V3 | SoC->gamecart reset signal |
TP54 | MC1_D0 | 3V3 | |
TP55 | MC1_CS | 3V3 | parallell ROM select (active-low) |
TP56 | MC1_CLK | 3V3 | |
TP57 | MC1_CS2 | 3V3 | AUXSPI select (active-low) |
TP58 | mRST | 3V3 | BPTWL reset (active-low) |
TP59 | mFE | 3V3 | BPTWL flash enable (cf. 78K0/Kx2 Serial Flash Programming protocol, see NEC/Renesas docs) |
TP60 | VOLP | 3V3 | volume + button (also RxD6 for 78K0 SFP. There's a series resistor to the physical button as protection against shorts) |
TP61 | VOLN | 3V3 | volume - button (also TxD6 for 78K0 SFP. There's a series resistor to the physical button as protection against shorts) |
TP62 | ATH_TX_H | 3V3 | AR6002 ANTD, "Control signal for shared antenna switch", probably enables Ath TX antenna |
TP63 | WL_TXPE | 3V3 | Old Wifi TX enable? |
(TP64 doesn't exist) | |||
TP65 | WL_RXPE | 3V3 | Old Wifi RX enable? |
TP66 | /WIFI_RST | 3V3 | New WiFi (Ath6k) reset (active-low) |
(TP67, TP68 don't exist) | |||
TP69 | SPI_MOSI | 3V3 | SPI bus |
(TP70 doesn't exist) | |||
TP71 | SPI_MISO | 3V3 | SPI bus |
(TP72 doesn't exist) | |||
TP73 | SPI_SCK | 3V3 | SPI bus |
(TP74, TP75 don't exist) | |||
TP76 | SPI_CS1 | 3V3 | SPI chip select 1 (PMIC) |
(TP77 doesn't exist) | |||
TP78 | SPI_CS3 | 3V3 | SPI chip select 3 (TSC) |
TP79 | SPI_CS2 | 3V3 | SPI chip select 2 (NVRAM) |
TP80 | SCL | 1V8 | CPU-TWL bus |
(TP81 doesn't exist) | |||
TP82 | SDA | 1V8 | CPU-TWL bus |
TP83 | PENIRQ | 1V8? 3V3? | touchscreen pen down |
TP84 | R7 | 1V8? | hinge magnet detect signal (active-low) |
TP85 | RESET | 3V3, but use as open drain/collector | CPU-TWL reset signal |
TP86 | P05 | 3V3? | dpad left button |
TP87 | P04 | 3V3? | dpad right button |
TP88 | P03 | 3V3? | start button |
TP89 | P02 | 3V3? | select button |
TP90 | P01 | 3V3? | B button |
TP91 | P00 | 3V3? | A button |
TP92 | PM_SLP | ? | ? |
TP93 | VCNT5 | ? | ? |
TP94 | GPIO330? | 3V3 | GPIO debug testpoint |
TP95 | R01 | ? | Y button |
TP96 | R00 | ? | X button |
TP97 | P09 | 3V3 | shoulder-L button |
TP98 | P08 | 3V3 | shoulder-R button |
TP99 | MUTE | 3V3 | ? (controlled by GPIO333 through U17) |
TP100 | P07 | 3V3? | dpad down button |
TP101 | HP#SP | 3V3 | audio out is headphones (1) or speakers (0). aka GPIO331 |
TP102 | P06 | 3V3? | dpad up button |
(TP103 doesn't exist) | |||
TP104 | nIRQ_O? | 3V3 | "powerbutton pressed" signal from the BPTWL to the CPU-TWL. aka GPIO332 |
TP105 | LDR20 | top LCD R.bit0 | |
TP106 | LDR21 | top LCD R.bit1 | |
TP107 | LDR22 | top LCD R.bit2 | |
TP108 | LDR23 | top LCD R.bit3 | |
TP109 | LDR24 | top LCD R.bit4 | |
TP110 | LDB21 | top LCD B.bit1 | |
TP111 | LDG21 | top LCD G.bit1 | |
TP112 | LDG22 | top LCD G.bit2 | |
TP113 | LDG25 | top LCD G.bit5 | |
TP114 | LDB20 | top LCD B.bit0 | |
TP115 | LDB23 | top LCD B.bit3 | |
TP116 | LDR11 | bottom LCD R.bit1 | |
TP117 | LDR12 | bottom LCD R.bit4 | |
TP118 | LDR15 | bottom LCD R.bit5 | |
TP119 | LDR25 | top LCD R.bit5 | |
TP120 | LDG20 | top LCD G.bit2 | |
TP121 | LDG23 | top LCD G.bit3 | |
TP122 | LDG24 | top LCD G.bit4 | |
TP123 | LDB22 | top LCD B.bit2 | |
TP124 | LDB24 | top LCD B.bit4 | |
TP125 | LDB25 | top LCD B.bit5 | |
TP126 | LDR10 | bottom LCD R.bit0 | |
TP127 | LDR13 | bottom LCD R.bit3 | |
TP128 | LDR14 | bottom LCD R.bit4 | |
TP129 | LDG10 | bottom LCD G.bit0 | |
TP130 | LDG11 | bottom LCD G.bit1 | |
TP131 | LDG12 | bottom LCD G.bit2 | |
TP132 | LDG13 | bottom LCD G.bit3 | |
TP133 | LDG15 | bottom LCD G.bit5 | |
TP134 | LDB11 | bottom LCD B.bit1 | |
TP135 | LDG14 | bottom LCD G.bit4 | |
TP136 | LDB10 | bottom LCD B.bit0 | |
TP137 | COM2 | ? | ? |
TP138 | LDB12 | bottom LCD B.bit2 | |
TP139 | LDB13 | bottom LCD B.bit3 | |
TP140 | LDB14 | bottom LCD B.bit4 | |
TP141 | LDB15 | bottom LCD B.bit5 | |
TP142 | INI | ? | LCD controller ? |
TP143 | GSP | LCD controller Vsync? | |
TP144 | GCK | ? | LCD controller ? |
TP145 | REV | LCD controller ? | |
TP146 | LS | LCD controller Hsync? | |
TP147 | SPL | LCD controller ? | |
TP148 | DCLK | LCD controller dot clock | |
TP149 | CAM_RST | 1V8? | Camera reset signal |
TP150 | COM1 | ? | ? |
(TP151 doesn't exist) | |||
TP152 | CAM_D4 | 1V8? | Camera parallell port (conn. thru RA7, 270Ω) |
TP153 | HSYNC | 1V8? | Camera horizontal sync/blank (conn. thru R133, 0Ω) (Aptina MT9V133-D LINE_VALID, active-low) |
TP154 | CAM_D3 | 1V8? | Camera parallell port (conn. thru RA6, 270Ω) |
TP155 | VSYNC | 1V8? | Camera vertical sync/blank (conn. thru R132, 0Ω) (Aptina MT9V133-D FRAME_VALID, active-low) |
TP156 | CKI | 1V8? | Camera clock something? (Aptina MT9V133-D EXTCLK? PIXCLK?) |
TP157 | CAM_D2 | 1V8? | Camera parallell port (conn. thru RA6, 270Ω) |
TP158 | CAM_D7 | 1V8? | Camera parallell port (conn. thru RA7, 270Ω) |
TP159 | CAM_D1 | 1V8? | Camera parallell port (conn. thru RA6, 270Ω) |
TP160 | X+ | ? | touchscreen |
TP161 | Y+ | ? | touchscreen |
TP162 | X- | ? | touchscreen, same net as Y- |
TP163 | Y- | ? | touchscreen, same net as X- |
TP164 | CAM_D6 | 1V8? | Camera parallell port (conn. thru RA7, 270Ω) |
TP165 | CAM_D0 | 1V8? | Camera parallell port (conn. thru RA6, 270Ω) |
TP166 | RCLK | 1V8? | Camera (conn. thru R100, 100Ω) (Aptina MT9V133-D EXTCLK? PIXCLK?) |
TP167 | CAM_D5 | 1V8? | Camera parallell port (conn. thru RA7, 270Ω) |
TP168 | VDD28 | 2.8V power rail | Only used by the camera. Generated by an LDO (U12) from VDD33 (Aptina MT9V133-D analog power rail?) |
(TP169 doesn't exist) | |||
TP170 | CAM_LED | Camera LED cathode? | Connected through Q13 and R68 to BPTWL. |
TP171 | RTC_INT | 1V8? | RTC->CPU-TWL interrupt |
TP172 | SD10_CLK | 3V3 | SD card |
TP173 | SD10_D0 | 3V3 | SD card |
TP174 | SD10_D1 | 3V3 | SD card |
TP175 | SD10_D2 | 3V3 | SD card |
TP176 | SD10_D3 | 3V3 | SD card |
TP177 | SD10_CMD | 3V3 | SD card |
TP178 | SD10_CP | 3V3 | SD card (card detect) |
TP179 | SD10_WP | 3V3 | SD card write protect |
TP180 | GND | ground | |
(TP181 doesn't exist) | |||
TP182 | SD10_VDD | 3.3V power rail | same net as VDD33 |
TP183 | AOUT | charging/battery status ? | |
TP184 | ADPO | charging/battery status ? | |
TP185 | SCL1 | 3V3 | BPTWL bus |
TP186 | SDA1 | 3V3 | BPTWL bus |
TP187 | SDI | 1V8? 3V3? | I2S bus |
TP188 | SDO | 1V8? 3V3? | I2S bus |
TP189 | WS | 1V8? 3V3? | I2S bus |
TP190 | SCLK | 1V8? 3V3? | I2S bus |
TP191 | MCLK | 1V8? 3V3? | I2S bus |
TP192 | PWSWO | 3V3? | powerbutton "output" from PMIC to BPTWL? |
TP193 | TH | ? | something battery charger? |
TP194 | VSHD | 5.0V power rail | Same net as VDD5. For LCDs. |
UTL-SUB-01 testpoints
number | name (TWL testpoint) | voltage standard | comment |
---|---|---|---|
TP1 | ? | ? | to TH1 component |
TP2 | GND | (GND) | ground |
TP3 | P06 | 3V3? | D-pad up |
TP4 | P04 | 3V3? | D-pad right |
TP5 | P05 | 3V3? | D-pad left |
TP6 | P07 | 3V3? | D-pad down |
TP7 | PWSW | ? | raw powerbutton input (to PMIC and BPTWL) |
TP8 | RED | open collector (at cathode) | Battery low LED (DL1) |
TP9 | YELLOW | open collector (at cathode) | WiFi indicator LED (DL4) |
TP10 | BLUE | 3V3? 4V2? (at anode) | Power on/good LED (DL2) |
TP11 | ORANGE | 3V3? 4V2? (at anode) | Charging indicator (DL3) |
TP12 | VDD42 | 4.2V power supply | Power supply for TP8/TP10 LEDs |
P16 pinout
The P16 pinout changed from what it was on the regular DSi. Some nets are now found in P24 instead (see below).
name | pin no | pin no | name |
---|---|---|---|
GND | 1 | 2 | GND |
GND | 3 | 4 | GND |
GND | 5 | 6 | GND |
SD10_CLK | 7 | 8 | GND |
VDD33 | 9 | 10 | SD10_D0 |
VDD33 | 11 | 12 | SD10_D1 |
GND | 13 | 14 | SD10_WP |
SD10_CMD | 15 | 16 | VDD33 |
GND | 17 | 18 | P08 |
SD10_D3 | 19 | 20 | VDD33 |
SD10_D2 | 21 | 22 | SD10_CD |
GND | 23 | 24 | GND |
GND | 25 | 26 | GND |
P24 pinout
P24 is a mezzanine connector for the VOLP/VOLN buttons and the shoulder L button (which were on P16 on the DSi).
name | pin no | pin no | name |
---|---|---|---|
GND | 1 | 2 | GND |
N/C | 3 | 4 | VOLP |
P09 (shoulder-L) | 5 | 6 | VOLN |
GND | 7-13 | 8-14 | GND |